My bad, I thought that your circuit has adjustable frequency.
OK, here is the correct timer schematic - Ufopolitics original.

...when i'll have time I will try to improve the timer circuit to make it fully adjustable - frequency and duty cycle separated pots...

@Ufopolitics
Could you please suggest the range of frequencies for the improved circuit?
Thanks

The carbon fiber makes sense. One of the Energy from the Vacuum series videos has A female researcher at a U.S. University that discovered how to make a negative resistor with carbon fiber. Sorry I do not remember which video it was. Great progress ufopolitics !

George

I believe it was in Part 1 EFV series and the researcher is Deborah D. L. Chung, Professor (Ph.D., Materials Science, Massachusetts Institute of Technology, 1977) Materials science and engineering, particularly smart materials, concrete, thermal management, battery electrode materials, carbon fibers and filaments, composites processing and interfaces, metal-matrix composites, electronic packaging materials, and activated carbon.

Vtech

__________________
'Get it all on record now - get the films - get the witnesses -because somewhere down the road of history some bastard will get up and say that this never happened'

General D.Eisenhower

http://www.youtube.com/user/blackchisel97?feature=mhum

This site (The Chung's Negative Resistance replication by JL Naudin) has some good info on different experiments with the negative resistor and how one can be made.

Hello Everyone!!

http://www.facebook.com/photo.php?fb...type=1&theater





The image above, shows the comparison (more and less) between the typical Square Wave progression We have so far (Red Sq Wave)... versus what We are looking for , in order to get Radiant at very low consumption from our side by reducing out T-On times (when increasing frequency)(Blue Sq.Wave)

Now this MUST be designed in a very smooth progression over time...For sake of simplicity and paper space I drew just five examples of frequencies...However, it should be understood that this process CAN NOT occur that abruptly.


The idea, is that We keep Her steadily in our System, with a very minimum T-On of pulses from our side, while T-Off keeps at the desired levels to allow Radiant to drive into our system.

I believe for a start we could set Trimmers at the adjusting parameters till we find the right values, then replace them by regular resistors.


The other IMPORTANT thing I found out ...is that a Couple of IN4148 Diodes, will do a better job as "Filtering" a much pure Radiant into our System, However, You will go "meters reading blind", therefore, I recommend to keep your regular diodes with end pin open, for reading Instrument purposes only.

Yes Carbon fiber is definitively a "Negative Resistor", Still lots of tests to be done on this subject, The only available fiber strands are very poorly build and very difficult to handle...they are not one solid piece of...but infinite amounts of threaded hair/like fibers that comes apart when building them into a Coil...But I got great results still like this...


Cheers


Ufopolitics

Hello Ufopolitics,
This content is currently unavailable, The page you requested cannot be displayed right now. It may be temporarily unavailable, the link you clicked on may have expired, or you may not have permission to view this page. -is what I'm getting from your link

@djex81 Yes, that's the one, Thanks.
Thanks
V

__________________
'Get it all on record now - get the films - get the witnesses -because somewhere down the road of history some bastard will get up and say that this never happened'

General D.Eisenhower

http://www.youtube.com/user/blackchisel97?feature=mhum

Hello Blackchisel,

I am having trouble with images...my sites do not have Certificate of Identity...(I want them that way!)...therefore images are not 'accepted' in the "Regulated Internet Networks"...
Do We have an Internal File Folder for each member so we could load pictures?

Thanks...
I will change the Facebook pic to Public, sorry about it

Cheers

Ufopolitics

Yes, there is a folder where you can upload an image, just scroll down the page when you post or reply to a post and you'll see a button -manage attachments. I use free Photobucket account to hold my photo/video files and 4Shared for pdf. files.

Thanks
Vtech

__________________
'Get it all on record now - get the films - get the witnesses -because somewhere down the road of history some bastard will get up and say that this never happened'

General D.Eisenhower

http://www.youtube.com/user/blackchisel97?feature=mhum

I forgot to mention earlier; this would probably work well here - PWM Generator * Regulator * for PWM Signal Pulse Frequency DIY Projects Motor | eBay

V

__________________
'Get it all on record now - get the films - get the witnesses -because somewhere down the road of history some bastard will get up and say that this never happened'

General D.Eisenhower

http://www.youtube.com/user/blackchisel97?feature=mhum

Link is working now, Thanks Ufopolitics. Yes, all it takes is a short, abrupt pulse to disturb vacuum. No need for 50/50. We can get neon working at either but at too much "cost" as far as hot side gets involved and we want to keep at minimal level.

Thanks
Vtech

__________________
'Get it all on record now - get the films - get the witnesses -because somewhere down the road of history some bastard will get up and say that this never happened'

General D.Eisenhower

http://www.youtube.com/user/blackchisel97?feature=mhum

YES!...Exactly Blackchisel!!

The idea is to keep pulses...very short interval pulses, once We got Radiant In...
I will define this in just two simple stages...
1- Get Our signal strong enough to generate the desired Electromagnetic Field Out (Our "Call" for Radiance) 50% +/-
2-Once We get Radiant Flow in...Then proceed to gradually decrease our T-On, till we get a minimal amount required in order to keep Her at our required levels.

Later on I would like to also "play" with the Top Peak Height ...Been able to rise Voltage/Amps levels at pulses...Independently of Oscillator.

However, in order to do this , we need to Isolate our Low Volt Signal at 555 from Drain-Source Channels related to Voltages/Amperage...An Opto-Electronic Isolator will do this job, between Output pin3 of 555 and gate input of MOSFET's...Then all we need to do is Increase V/I at the Source Channel ,separate from the pulses...

This adjustment will work in "harmony" when signal is becoming a very short-timed pulse...rising then to higher peak levels...to compensate-balance our magnetic field strength, not allowing to get weaker because of Time shortening...


Cheers


Ufopolitics

Hi Ufo,

I notice in the circuit that all the NTE2397 Mosfets are attached by their body to a support that is being used as the DRAIN, so I expect that the DRAIN middle leg and the Mosfet body are the same connection, does it matter if you use the leg, or is it better to use the body or doesn't it matter, and if you use the leg should the body be insulated from the support. If the support is used as the DRAIN does it matter what material is used. Aluminium would probably be the easiest to use.

Thanks netica

I wonder how this cold electricity would split water for hydrogen production?

__________________
Half of the Answer is knowing the right Question

It shouldn't. As you are not dealing with a dipole based energy. If in fact cold current is being produced it will not rectify and polarity will not matter.

Matt

__________________
Gone Baby Gone!!!

Hello Netica,
Yes, all MOSFET's are attached to a Drain Bus Bar, that serves as Heatsink and as a Conductor bar for Drain transmission. Therefore I CUT all middle legs from my MOSFET's, it will only bring confusion to have them running also in your circuit board, no need to.

Yes Aluminum works excellent, and if want to go a bit 'fancier' could add a copper strip all the way to connector end..


Regards

Ufopolitics

Hey Matt!!...long time no see you?!

I was waiting to hear from you...thought you were gonna do your own testing ...

Anyways...Yes, I have done Electrolysis and a "very clean one" by just adding 2 tea spoons of Salt to water, (as a Catalyzer) the speed is amazing.

And it DOES HAVE POLARITY Matt!!...remember it comes "VERY WELL" rectified from the Diodes Wall...

By the way..I like how you'd say...
..."If in fact cold current is being produced ..."

Is there any more "Testing" pending to be done Matt??...to certainly accept by "Your Majesty" that it is in fact, Cold Electricity?

Give me more "testings"... and I will be more than happy to please your Royal desires...Sir

Thanks

Ufopolitics

Hi Blackchisel
As I was reading the posts I looked over your schematic again and again and relaized this may be what I have been looking for to use in my Watson machine. On your version is the coil mono directional or bifiliar? And does it have an iron core?
Thanks
Bizzy

__________________
Smile it doesn't hurt!

Jesus said,"...all things are possible through God." Mk10:27

Hi Bizzy, Well. they're not mine . Also, in lower two diagrams battery symbol is drawn incorrectly (upside down). They work with or without core and can also run in bifilar mode.
For Watson replication I'll suggest hollow iron core, not air. But...if you look at Ferris Wheel do you see the resemblance on steroids
What happens with magnetic field when piggyback neo starts to "skate"

Thanks
Vtech

__________________
'Get it all on record now - get the films - get the witnesses -because somewhere down the road of history some bastard will get up and say that this never happened'

General D.Eisenhower

http://www.youtube.com/user/blackchisel97?feature=mhum

Hi VTech
Yes I noticed the batteries were upside down
I also think I have just the right hollow iron core I can use. What guage wire and how many wraps would you recommend? I it is hard to determine an an exact amount but a ballpark figure would be greatly appreciated.
Thanks
Bizzy

__________________
Smile it doesn't hurt!

Jesus said,"...all things are possible through God." Mk10:27

Hi Bizzy, I wouldn't go over 200T. I don't know how big you're planning to go with this setup. I would use AWG#20 and wind on 1/3 core length from the rotor side, not the entire core length. I would only use some tape and wind directly on the core, no spool.
There is one type of masonry anchor (I'll try to find pic.) which works good with smaller setups. This anchor bolt is made of alloy which contains zinc,iron and few other metals. You have to remove inner bolt and use hollow tube. Tube has oval hole in the middle. When you wind, don't go over it but stay in front solid part. Core is about 65mm long by 12mm OD by 10mm ID. They would work with neo magnets of same diameter (rotor magnets) and relatively small rotor. I'll try to find more in my papers but I have more than one backup files storage and they are few GB each

Thanks
Vtech

__________________
'Get it all on record now - get the films - get the witnesses -because somewhere down the road of history some bastard will get up and say that this never happened'

General D.Eisenhower

http://www.youtube.com/user/blackchisel97?feature=mhum

Hi Vtech
Ok this is a great help thanks
Bizzy

__________________
Smile it doesn't hurt!

Jesus said,"...all things are possible through God." Mk10:27

Hi Bizzy!

I am having much better results with a Bifilar Coil, but NOT series but Parallel connected between wires.
I also got better results with a Hollow Core (Air), steel cores tends to retain too much memory and ends up permanently polarizing at ends, which is not good for this purposes, since we have Switching polarities EMF (Electro-Magnetic-Field) . The "Ideal Core" would be made of some Alloy like a Nano-Crystalline material, or like Blackchisel mentioned, where steel is not a 100% of its composition.

Cheers and good testing!!

Ufopolitics

Use 2 big neo's in the same direction on each end of soft iron welding rods and heat up the metal, good and hot. When the metal get good and hot keep it hot for bit then dump it in water with the magnets still attached. Maybe more than one time if you feel the need.
This crystallizes the soft iron and eliminates the memory. Then you can paint them or something to isolate eddies.
The copper clad rods will not work. Cheap normal grade 3/32 welding rods work the best.
Insert the welding rods with the polarity opposite of what you would expect out of the coil.
Air cores usually use more current for the same amount of return. Usually.

Matt

__________________
Gone Baby Gone!!!

Have you thought of using a para-magnetic material as a core?
A while back Min2oly used a coil with a para-magnetic core, and got good coil saturation, and it had less drag on the rotor.
I couldn't find the video on his channel anymore, so he might have removed it, but his results interested me. I can't remember what he used for the core, but I tried molybdenum, and couldn't get it to glue together well enough to fill a core with it.

Either way, it might just fit the bill for what you are looking for, and figured it was worth throwing out there

N8

__________________
The absence of proof is not proof of absence

Hey Matt,

That's a great idea, to crystallize the soft iron...
I am using an Air Core at this point to test Induction from Radiant Field within the Hollow Core, by adding a Secondary of finer wire, also hollow core...with great results. But, there is a delay in the pulses caused by the propagating magnetic field to reach secondary, besides do not get brighter Light as output from Primary RE.
I am certain that have to 'bring' to center of secondary, the Hot side pulsating field poles...to enhance RE Induction on secondary.
I am building an 'Umbrella' type design in steel for both separate poles.
Already test it with two old transformer E Frames and works excellent, but I want the 360 degrees EMF's in.

Cheers

Ufopolitics

It really works well. But you have to do it under magnetic field. I have only done it for direction induction. Monopoles and motors and stuff but... So if your going in both direction you might try setting it up sideways of something along that line. You want the crystallization to line up But which way it lines up might not matter. Just have to try.

Matt

__________________
Gone Baby Gone!!!

Hi N8
Do you have a list of other paramanegtic materials?
I am still in the process of testing capacitor ratios on my machine but I will soon be done with that and hope to test the coils by next week.
Thanks
Bizzy

__________________
Smile it doesn't hurt!

Jesus said,"...all things are possible through God." Mk10:27

Hey Bizzy,
I did manage to find a website with a list of all the elements, and their magnetic properties, which is pretty cool to look through.
here is the link -
Magnetic Type for all the elements in the Periodic Table
and I was really suprised to see this on the list as paramagnetic
Neodymium Paramagnetic
makes me wonder how other paramagnetic elements would do if made into permanent magnets....
there is also a lot of information on wikipedia on this subject, and might be worth looking at.
hope that helps, and I look forward to seeing what you come up with
N8

__________________
The absence of proof is not proof of absence

Hi Ufoolitics
Ok thanks for the advice. I made a 200 turn coil with a hollow steel/zinc core like blackchisel described. I am going to order more magnet wire today so I can make a bifiliar coil as well as an air core coil. It is my hope to be able to compare them side by side then share my results using my machine.
Thanks
Bizzy

__________________
Smile it doesn't hurt!

Jesus said,"...all things are possible through God." Mk10:27

Hi N8
Thanks for the list that does open up some interesting ideas which deserve to be explored. I will have to see where my next battery of tests takes me.As I mentioned to ufopolitics I hope to make up some more coils to test them side by side in my machine. So hopefully I can incorporate the paramagnetics into the tests as well.
Thanks
Bizzy

__________________
Smile it doesn't hurt!

Jesus said,"...all things are possible through God." Mk10:27